1/7/2024 0 Comments Windows terminal cooltermSettings with regard to received data can be adjusted here. Other special character handling may also impact UTF-8 display. Note that UTF-8 may not be supported for all platforms and/or font selection. If Local Echo is enabled while this feature is enabled as well, locally echoed characters will cause the display to refresh immediately.Įnabling this feature will ignore received LF characters (ASCII code 10) and will prevent CoolTerm from interpreting rogue LF characters as new line characters.Įnables displaying plain text using UTF-8 encoding for received data in UTF-8 format. If checked, the reception of a FF character (ASCII code 12) will clear previously received characters from the receive buffer and thus clear the screen.Įnabling this feature will prevent the display from updating until a EOT (ASCII code 4) character is received, at which time the display is updated with the contents from the receive buffer. If checked, received bell characters (ASCII code 7) will play a terminal beep. When either character is received (or typed with local echo enabled) the previous character in the ASCII viewer is deleted. If checked, Backspace (BS, ASCII code 0x08) and Delete (DEL, ASCII 0x7f) characters will be visually handled in ASCII View mode. If checked, non-printable characters (ASCII codes 0 to 31) will be displayed as a period character in ASCII View mode. If checked, ASCII Escape Sequences will be removed from the received data in ASCII view mode.Ĭonvert Non-printable Characters (ASCII View) The minimum number of consecutive spaces required for replacement can be specified below.įilter ASCII Escape Sequences (ASCII View) If checked, consecutive space characters will be replaced by single TAB characters. The column width can be specified in the field below. If enabled, text will be aligned on a specified column width in plain text view by replacing received TAB characters with spaces. If checked, TAB key presses are replaced with the number of spaces specified in the field below. If checked, locally entered data will be echoed in the terminal window. When in Line Mode, the contents of the send buffer are terminated with the character(s) selected here before they are sent. Select any line to add it to the send buffer.ĭefines what character(s) to send when the Enter key is pressed. Alternatively, the square button to the right of the command line field can be pressed to show a history of previously sent lines. the up and down arrow keys can be used to send previously typed lines. one line of text) are sent when the enter key is pressed. Characters typed in this field are added to a send buffer. When in Line Mode, a command line field is visible in the terminal window. In Raw Mode every key is sent via the serial port immediately as it is pressed. These options are accessible regardless of the connection state of the serial port. Options related to terminal behavior are adjusted here. This can be used to set the initial state of the RTS and DTR status lines when the respective hardware flowcontrol options are not enabled. Should the serial port still not be available for selection, ensure that the proper drivers for the serial port are installed.Īdditional information (such as driver names and rated speeds) about the selected port can be displayed by clicking the bevel button to the right side of the Port: popup menu. in case it is a USB to Serial port adapter that was connected after CoolTerm was started) push the Re-Scan Serial Ports button. If the serial port to be used is not listed in the popup menu (e.g. Press Disconnect when finished with the session to ensure it is available for other programs to use.Select the serial port from the popup menu and configure its settings according to the requirements (Baudrate, Data Bits, Parity, etc.) of the connected hardware. If either time you do not see the Xbee's port as an option, or if you plug it in with the options box open, press the Re-Scan Serial Ports button show in the red box from the above image.ĥ) Now press Connect for each terminal and you can now type in either and it will transmit to the other. No additional changes are necessary for standard comms.Ĥ) Repeat the above step for the other Xbee in the other port. CoolTerm Terminal (or equivalent terminal ability): Download Home Page (Windows 64-bit link)ġ) Attach Xbees to SainSmart boards and plug into computerĢ) Open two CoolTerm Sessions and click on one of the Options buttons.ģ) In the Options pop-up select the COM Port of either Xbee and then go into the Terminal Tab and select Local Echo (in order to see what is being transmitted).If you need to configure them see this tutorial: Xbee Basic Setup
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |